Starter scheme of turning on of fluorescent lamps

Single-tube schemes of inclusion

The simplest starter scheme of inclusion is provided on fig. 1. Basic elements of this scheme: the starter which is switched on parallel to the lamp and the throttle connected consistently to it.

Схема детекторного приемника с одноламповым усилителем низкой частоты

The scheme of the detector receiver with the single-tube low-frequency amplifier.

The starter represents the small gazorazryadyony lamp of the glow discharge (fig. 2).

The glass kolyoba is filled with inert gas (neon or mix helium-hydrogen) and is located in the metal or plastmasyosovy body on which upper cover there is the smoyotrovy window.

In some designs of starters the observation port is absent. The 2nd electrofood has the starter. Distinguish asymmetrical and symmetric konyostruktion of starters. In asymmetrical starters 1 electrode motionless, and the 2nd - mobile, is made of bimetal.

Простейшая стартерная схема включения

Figure 1. The simplest starter scheme of inclusion.

Now the greatest rasproyostraneniye was received by the symmetric design of starteyor at which both electrodes are produced from the bimeyotall. This design has the number of advantages in comparison with asymmetrical.

Ignition tension in the starter of the glow discharge is chosen so that it was less rated voltage of network, but it is more than operating voltage which is established on the lyumiyonestsentny lamp at its burning.

At inclusion of the scheme (fig. 1) on nayopryazheny networks it completely will be attached to the starter. Electrodes of the starter are opened, and in is mute there is the glow discharge. In the chain there will pass small current (20 — 50 mA). This current nayogrevat bimetallic electrodes, and they, being bent, will close the chain, and the glow discharge in the starter will stop. Current which will warm up cathodes of lamps will begin to pass the connected cathodes through the throttle iposledovatelno. The size of this current is defined by the induced resistance of the throttle chosen so that current of preliminary heating of cathodes by 1,5 — 2,1 times exceeded rated current of the lamp. Duration of preliminary heating of cathodes is defined by time during which electrodes of the staryoter remain closed. When electrodes of the starter are closed, they cool down, and after the certain period called by engagement time, electrodes razyomykatsya. As the throttle possesses big индуктивностыо, at the time of disconnection of electrodes of the staryoter in the throttle there is the big impulse the napryazheyoniya lighting the lamp.

Стартеры тлеющего разряда

Figure 2. Starters of the glow discharge.

After ignition of the lamp in the chain current, ravyony to the lamp rated working current will be established. This current obuyoslovit such voltage drop on the throttle that the nayopryazheniye on the lamp will become approximately equal to the half of rated voltage of network. As the starter вклю­чен parallel to the lamp, tension on will be mute equally to tension on the lamp and because it insufficiently for ignition of the glow discharge in the staryoter, its electrodes will remain opened at the lamp goreyoniya.

The possibility of ignition of the lamp depends on the dlitelyyonost of preliminary heating of cathodes and size of the current passing through the lamp at the time of disconnection of electrodes of the starter. If the rupture of the chain occurs at small value of current, then size induced in the throttle э. of page and, therefore, tension attached to the lamp can be insufficient for its ignition, and the lamp will not be lit. Therefore if in the first attempt the starter does not light the lamp, he at once will automatically repeat the described process until there is ignition of the lamp. Parallel to electrodes of the starter the kondenyosator with a capacity of 0,003 — 0,1 microfarad is included. This condenser is obychyono placed in the starter body.

The condenser vypolyonyat 2 functions: reduces the level of radio interferences, vozniyokayushchy at engagement of electrodes of the starter and created by the lamp; on the other hand, this kondensayotor exerts impact on processes of ignition of the lamp. The condenser reduces the impulse size the napryazheyoniya formed at the time of disconnection of electrodes of the staryoter and increases its duration. In the absence of the condenser tension on the lamp very quickly vozyorastat, reaching several thousand volts, but duration of its action very small. In these usloyoviya reliability of ignition of lamps sharply decreases. To Kroyoma of that, turning on of the condenser parallel to elektroyoda of the starter reduces probability of welding or as speak, the sticking of electrodes which is turning out in the reyozultata of formation of the electric arc at the time of disconnection of electrodes. The condenser promotes fast arc extinction.

Схема компенсирующей катушки

Figure 3. Scheme of the neutralizing coil.

Use of condensers in the starter does not provide full suppression of the radio interferences created by the fluorescent lamp. Therefore it is necessary to install in addition on the entrance of the scheme (fig. 1) 2 condensers with a capacity not less than 0,008 microfarad everyone connected consistently and to ground the average point.

One of the recommended ways of decrease in level of radio interferences is application of throttles with the symmetrized winding (fig. 1). The winding of the throttle is separated into 2 absolutely identical parts having equal number of the rounds which are reeled up on one general core. Each part of the throttle is connected consistently to one of lamp cathodes. At inclusion of such throttle both of its cathodes work with the lamp in identical conditions that reduces the level of radio interferences. Now, as a rule, the throttles released by the industry are produced with the symmetrized windings. In the scheme in fig. 1 because of availability of the throttle current through the lamp and mains voltage will not match on the phase, i.e. they will not reach at the same time the zero and maximum values. As is well-known from the alternating-current theory, in this case current will lag behind on the phase mains voltage on some corner which sizes is defined by the ratio of induced resistance of the throttle and pure resistance of all network. Such schemes are called lagging behind.

In some cases uses of luminescent lamas, it is required to create such conditions when current through the lamp would advance mains voltage on the phase. Such schemes are called advancing. For performance of this condition consistently with the throttle the condenser which capacity is calculated so that its capacitive reactance was more induced resistance of the throttle turns on.

In the advancing ballast during ignition of the lamp current of preliminary heating of cathodes has insufficient size. For elimination of this phenomenon it is necessary to increase current of preliminary heating for the period of ignition of the lamp that can be made if partially to compensate capacity by inductance. The chain of the starter joins additional inductance in the form of the neutralizing coil (fig. 3). At short circuit of electrodes of the starter this neutralizing coil turns on consistently with the throttle and the condenser, the general inductance of the scheme vozrastayot, and together with it current of preliminary heating increases. After disconnection of electrodes of the starter the komyopensiruyushchy coil is switched-off, and she does not participate in the operating duty of the lamp. The inductance of the additional coil compensates the capacitor capacitance, ustanovyolenny in the starter. Therefore the dopolniyotelny condenser with a capacity not less than 0,008 microfarad which is switched on parallel to the lamp and carrying out in this case the role of the noise suppressing condenser is entered into the scheme.

Схемы подключения двух люминесцентных ламп

Schemes of connection of two fluorescent lamps.

One of shortcomings of the considered schemes — low power factor. It makes size 0,5 — 0,6. The Puskoreguliruyushchy devices (PRA) executed on the basis of these schemes belong to group of so-called noncompensated devices. When using tayoky devices, according to the rules of the device of elektroyoustanovka (RDE), for increase in low power factor it is necessary to provide the group komyopensation of electrical power factor providing its doyovedeniye for all lighting installation to the veliyochina 0,9-0,95.

At impossibility or the economic neeffektivyonost of application of group compensation of electrical power factor use schemes in which in addition parallel to the lamp the condenser of sufficient capacity chosen so that the electrical power factor of the scheme raised up to the size of 0,85-0,90 (fig. 1) turns on. PRA made according to this scheme is called compensated. Calculations show that at the voltage of 127 in for the 15 and 20 W lamps the condenser has to have capacity 3,5-4 microfarad, for the 30 and 40 W lamps at voltage of 220 V the capacity of the konyodensator is 3-5 microfarad.               

The main lack of starter schemes of ignition — their low reliability which is caused, unreliability of operation of the starter. Reliable operation of the starter also depends on the voltage level in the power line. With undervoltage in the power line time necessary for the warming up of bimetallic electrodes increases, and at reduction of tension more than for 20% rated the starter does not provide engagement of electrodes at all, and the lamp will not be lit. Means, with reduction of tension in the power line time of ignition of the lamp increases.

At the fluorescent lamp in process of aging increase in its operating voltage, and at the starter is observed, on the contrary, with growth of service life tension of ignition of the glow discharge decreases. In result of it it is possible that at the burning lamp the starter will begin to work and the lamp dies away. At disconnection of electrodes of the starter the lamp lights up and observed migayony lamps again. Such blinking of the lamp, in addition to caused by it unpleasant visual feeling, can lead to overheating of the throttle, its exit out of operation and damage of the lamp. The similar phenomena can take place when using old starters in network with lowered" the voltage level. At emergence of blinkings the lamp needs to replace the starter with new.

Starters have considerable dispersions of time of engagement of electrodes, and it very often insufficiently for reliable preliminary heating of cathodes of lamps. As a result the starter lights the lamp after several intermediate attempts that increases duration of the transition processes reducing the term of the sluzhyoba of lamps.

Common fault of all single-tube schemes - the nevozyomozhnost to reduce the pulsation of the luminous flux created by one lyuminestsentyony lamp. Therefore such schemes can be applied in rooms where several lamps are established, and in case of their use for group of lamps it is recommended to include for the purpose of reduction of the pulsayotion of the luminous flux of the lamp in different phases of the three-phase chain. It is necessary to aim at that illumination in each point was created not less than from 2-3 lamps included in different phases of network.

Two-lamp schemes of inclusion

Application of dvukhyolampovy schemes of inclusion gives the chance to reduce the pulsation of the total luminous flux as pulyyosation of each lamp happen not at the same time, and to some shift on time. The total luminous flux of 2 lamps will never be equal to Poyoety 0, and fluctuates about some sredyony value with the frequency, smaller, than at one lamyopa. Besides, these schemes provide high коэф­фициент set capacities lampa-PRA

Схема с расщепленной фазой

Figure 4. The scheme with the split phase

The greatest distribution was gained by the dvukhlampoyovy scheme called often by the scheme with the split phase (fig. 4). The scheme consists of 2 elements branches, lagging behind and advancing. In the 1st branch current lags behind on the phase tension on the corner 60 °, and in the 2nd - opeyorezhat on the corner 60 °. Thanks to it current in external the tseyopa will almost match on the phase tension, and the electrical power factor of all scheme will make size 0,9-0,95. This scheme can be carried to group kompensiyorovanny, and in comparison with the single-tube noncompensated scheme it has that advantage that it is not required to take additional measures for the electrical power factor povyyosheniye.

At production of PRA according to this scheme the general consumption of constructional materials is less, than for single-tube devices. Now the large number of different types of the devices executed according to this scheme is issued.

Схема последовательного включения люминесцентных ламп

Scheme of consecutive turning on of fluorescent lamps.

Consecutive turning on of fluorescent lamps, in some practical cases can arise need for consecutive turning on of fluorescent lamps: for example, it will be required to include in network with voltage of 220 V two 15 or 20 W lamps having operating voltage about 60 Century.

For consecutive inclusion 2 lamps, identical on power, have to be taken. It is not recommended to include consistently lamps of different power as the working current at such lamps is not identical in size. In qualities of ballast resistance the standard throttle expected the total power of consistently included lamps can be used.

In the scheme in fig. 5a starters have to be taken on the half of mains voltage, i.e. for network of 220 V the starter gets out to tension 127 V. Nedostatok of this scheme — at the asymmetrical design of the starter chances of their non-simultaneous work that can lead to cold ignitions of lamps.

In the scheme in fig. 56 preliminary heating of 2 cathodes of lamps is carried out by the special filament-supply transformer which is switched-off by the starter after disconnection of its electrodes. In this scheme you use 1 starter expected the rated voltage of network.

COMMENTS
  • To add the comment

0000000000000000
Top